Need Support? Let’s guide you to the right answer or agent.

OpenRoads Ideas Portal

ADD A NEW IDEA

Functional Areas

Showing 941

Allow user to define width of superelevation section graphic.

Currently, the graphic representing the superelevation section is hard coded to use the radius of the smallest curve in the alignment. If the radius of the smallest curve is 50 meters or more, the section width is hard-coded to 50 meters. If t...
7 months ago in OpenRail Designer / OpenRoads Designer / Superelevation 0 Future consideration

Ability to save frequently used slopes in the "create slope to target" tool dialogue.

It would be very helpful if we could save our frequently used slopes to a pull down list in the "create slope to target" tool dialogue. Currently you have to type in your desired Cut and Fill slopes every time you use the tool. It would be much be...
almost 2 years ago in Modeling / OpenRail Designer / OpenRoads Designer / OpenSite Designer 0 Future consideration

Add ability to match level when importing features from graphics

When I import features from graphics into a field book, the program does not set the correct level (match level) for most features. If we can get it to match the level correctly, it would save a lot of time. To take it a step further, it would be ...
almost 2 years ago in OpenRail Designer / OpenRoads Designer / OpenSite Designer / Survey 1 Future consideration

Automatically calculate values when inputting into property fields

When inputting numbers into property fields, ORD can automatically calculate them for you. Example: Survey field team shoots the top of casting elevation of a manhole at 500ft, then shoots again for a bottom invert of the manhole but only leaves a...
7 months ago in OpenRail Designer / OpenRoads Designer / OpenSite Designer / User Interface 0 Future consideration

Geometry builder fix components

As in the geometry connector, the geometry builder needs to be able to fix certain elements
almost 2 years ago in Geometry / OpenRail Designer / OpenRoads Designer / OpenSite Designer 2 Future consideration

Add ability to modify annotation group from reference without overrides

In 21 R2, the capability was added to override an annotation group. This appears the only way to be able to modify a local anno group from a referenced dgn. I would advocate to add the ability to override anno groups in the dialog when creating sh...
almost 2 years ago in Drawing Production / OpenRail Designer / OpenRoads Designer / OpenSite Designer 0 Future consideration

Horizontal and vertical geometry - edit vertical elevations/profile in plan view, improve geometry snap rules/constraints.

We have used the horizontal and vertical geometry tools to create terrain models for site design of rest areas. We have found this to be very inefficient and time consuming. For example, the rest areas typically have sidewalks that vary in width, ...
about 1 year ago in Geometry / OpenRail Designer / OpenRoads Designer / OpenSite Designer 0 Future consideration

In OpenRoads Designer Explorer, add a feature list for terrain features, similar to the new "point filter" dialog.

Currently features that make up a terrain can be viewed, added, or removed graphically. Would like to be able to see all terrain features in a table or list view, similar to point filter list. In addition, be able to add and remove or temporarily ...
about 1 year ago in OpenRail Designer / OpenRoads Designer / OpenSite Designer / Terrain 0 Future consideration

Need the ability to define sequence number other than at the end of the filename

We have a standard naming convention that uses sequence numbers which are in the middle of the filenames. This has been our standard for over twenty years. Additionally, we require each sheet to be in a separate file for multiple flexibility and a...
7 months ago in Drawing Production / OpenRail Designer / OpenRoads Designer / OpenSite Designer 0 Future consideration

Allow entering a degree of curve (d 00^00'00") as the Radius of the Alignment Table Editor.

When creating curves, an ORD user is allowed to enter a degree of curve (d 00^00'00") as the Radius. Put the same functionality in the Alignment Table Editor.
7 months ago in Geometry / OpenRail Designer / OpenRoads Designer / OpenSite Designer 0 Future consideration